We can supply you with the skill and knowledge for your KNX project.

If you wish to do this, you will need to adhere to the specification of the KNX Power Supply.

How to extend NTC or PTC temperature probes

A standard twisted pair KNX line can support 40-50 telegrams per second.

The process to enable the ETS online catalog for KNX devices is detailed in this step by step guide.

Thankfully, the way KNX works means you will be able to replace the part with a newer version even if it is from a different manufacturer.

By using the correct hole saw, the Kaiser back box will be countersunk into the wall ensuring the KNX or Crestron keypad will sit flush to the wall hiding the back box completely.

How to tackle problems and warnings when using ETS Professional to create projects and commission KNX devices.

On the Gira G1 KNX room controller, terminating the Cat6 or Cat7 cable incorrectly can cause issues with the door communications display or cause intermittent issues with the network connection. Find out how to.

A document detailing how to configure Intesis WMP gateways with Unifi Ubiquiti Wi-Fi. Wi-Fi settings for different generations of gateway.

Step by step guide of what you need to do should your purchased item become faulty.

Yes it can, by adjusting the DIP switches mounted under the label.

The simplest way is to press the programming button. If the programming LED lights up then it is connected to the bus.

The G1 models that connect to KNX via an Ethernet connection can.

This is accessed via the menu of the device.

Zennio Lumento with Collingwood Lights constant current

If the address is known, use ETS to overwrite the current address. If the address is unknown..

Ivory Egg standard delivery times.

Yes, there is...

If you have misplaced your ETS dongle or it has broken you may be able to arrange a free of charge replacement with the KNX Association...

It is possible to purchase a 230v base separately. The part code is 2331 01.

A separate relay module is available which can be installed into the unit.

​There are two LEDs on the front of the unit labelled RUN/DIAG and KNX...

How to configure IntesisBox with HVAC Mitsubishi VRF AE200 controller to use actual room temperature measured in KNX thermostat in a smart home

Control of velux windows with knx

At a product level they are exactly the same device, it is only when configured in ETS that they become different...

The number of devices in each line segment is limited to 64 to ensure KNX telegrams are not affected...

KNX is a extremely scalable system but what is the theoretical number of devices within a KNX system.

Care when selecting Intesis WMP interfaces for Fujitsu AC models depending on supplied 2- or 3-wire wall controllers for Control4 Elan Crestron. Drivers from Chowmain

How to log in to your account.

After a power outage or system reset the Fujitsu AC system scans its bus for controllers, if the Intesis KNX gateway isn't ready the units won't communicate.

Every line must have its own power supply including any area or backbone lines...

How to place an online order

Although KNX is standardised not all manufactures implement the full KNX stack. Control4, RTI and Savant all support only some gateways, find out the reason why.

If you are having trouble connecting to the KNX bus via USB there are a couple of quick fixes...

This error can occur when the application in ETS and the firmware in the device are on different versions.

Kaiser keypads should be mounted with the keypad fixing screws at the top and bottom for the widest range of compatibility with keypads.

Using a button sequence programming mode can be triggered from the front plate.

When an actuator dimming channel is off there is still residual voltage at the output

how to interface the mitsubishi ECODAN hot water system to KNX

A short guide on how to order inscribable items via Gira's online inscription service.

Some KNX blind actuators add a 20% overrun to the parametrised run time.

As the KNX bus is SELV (Safety Extra Low Voltage) there are no restrictions on placement. The only caveat is the effect the moisture may have on the device....

If the manifold controller has triac outputs (silent switching) then you cannot use the output to drive a pump as they are designed for low current restive loads...

After updating the Gira G1 KNX controller to version 2.0.442 a password is required to access the setting of the device.

Intesis Panasonic PA-RC2-WMP comms problem in AUS/NZ

KNX Introduction Series part 3 - resources and training

Battery 6V ensure charged fully before installation

Current warranty periods from our manufacturers.

Attending site is not a service we offer however we can provide support over the phone and if needed can remotely access your laptop...

There are two types of IP connection to a KNX system each with their own purpose- find out how to spot the difference.

If your KNX system was installed before 2014 the dimmers will not be suitable for mains LEDs...

Step by step help guide to add ETS apps and licenses to ETS

To connect to the KNX bus you will need a IP Interface, IP Router or USB Interface...

Ivory Egg returns policy without the jargon.

The Gira S1 needs to be powered and connected to the WAN before configuring the device in the Gira Portal.

An Interface is just for connecting to the KNX bus, an IP Router can also be used for connecting KNX lines over an IP Backbone.

Reseting the parallels network connection will clear the issues with KNX IP Routers not being found in ETS.

This is a 'feature' of Theben relay actuators. If a relay channel is parameterised as a pulse function but is triggered as part of a scene the pulse function will not be executed; the channel will switch on, but not time off.

To invert a logic output in the Gira Project Assistant logic editor you need to right-click​ on the output and select Invert.

Check your current AC unit compatibility with Intesis' range of HVAC integration products

A useful process for resetting to DHCP or clearing the local physical addresses.